We have stumbled upon this article on AC HVAC Repair listed below on the web and thought it made perfect sense to write about it with you on this page.

Watch our Video

HOW TO LOCATE YOUR FURNACE

Air circulation in your home

If you have central heating, the furnace (also known as an air handler) in your home will heat your air in the winter while the blower motor circulates the air throughout your home. The AC evaporator coils for your air handler remove heat and humidity in summer. After your furnace heats or cools your air, it is then supplied to the duct system and the air begins flowing through your registers.

How many air systems run in your home?

Your thermostat is what sets the temperature in your home for your comfort. The number of thermostat(s) determine how many systems work to regulate your indoor air for heating and cooling.

Improve IAQ with Duct cleaning

Air duct cleaning can help reduce allergies from dust and other pollutants. Pollen, dust, and mold spores can get trapped in your duct work, which means that it's being continuously circulated throughout the air you breathe at home.

According to the U.S. Department of Energy (DOE), 25 to 40 percent of the energy used for heating or cooling a home is wasted. Contaminants in the heating and cooling system cause it to work harder and shorten the life of your system. Although filters are used, the heating and cooling system still gets dirty through normal use.

The National Air Duct Cleaners Association (NADCA) recommends air duct cleaning for improvement of Indoor Air Quality (IAQ). A certified duct cleaning will include cleaning of the furnace, the main trunk line [for air circulation] and all vents (including supplies and returns) each cleaned out individually.

Where is a furnace/air-handler typically located in a home?

Typically your furnace is centrally located in the home. It is usually located in an area such as a utility closet (by a cold air return), garage, attic, basement, or crawlspace; in the case of a heat-pump (a dual-system) it will be located outside of the home. When your system is run with a heat pump, it is likely a typical duct cleaning will include cleaning of evaporator coils with full system cleanings. Your furnace is usually located by other mechanical equipment such as the hot water heater, a [permanently installed] central vacuum cleaner, or a water softener, if this equipment is installed in your home.

HVAC Services https://www.advantaclean.com/blog/2014/november/how-to-locate-your-furnace/

Why Heating Repair is Unavoidable When Upkeep Is Ignored

You can maintain an furnace system a number of different ways. Chances are good that the system shall be running all day long in the winter. Actually, it is usually on more than it needs to be because it is unable to maintain an efficient environment. There there are various areas in the heating section to look at when troubleshooting for efficiency.

The Air Filter

This is the part you usually hear people talking about most frequently, but so few people take the advice and do anything about it. When there is a obstruction, you either run the chance of not circulating heat properly or perhaps igniting a fire.When the air conditioner filter becomes dirty air cannot flow through either which means the unit must work harder and will also mean a risk of fire. When a system works too much, it costs more to operate. You want to obviously remove any likelihood of fire. In both situations it is not good for reassurance or your finances.

Try The Blower

Examine the blower blades to make sure they are clean. If you find any buildup of grime and debris, your fan will need to work overtime to blow the air around, and the heating system will be overexerting itself. Therefore the system is over taxed and costing extra money to run.

Check To See That The Fire Damper Works

Be sure to check your fire damper for proper operation. This will make sure that the fir risk is minimal and the system will work more efficiently.

The Flex Duct

Air ducts can get damaged over the years. If there are obstructions or if the duct has collapsed anywhere the furnace system will think the right temperature has been achieved, which can be wrong. When this will happen the system works harder to do its job but is going to be unable to reach the desired temperature range.

Make Sure The Insulation Is Secure

Insulation is usually missed but is among the most regular reasons why an furnace system fails. Take take time to look at the insulation in between the duct work and the outside to make sure it has not come loose. When this has happened the system will work more than desired while trying to reach the best temperature.

Ductwork Needs To Be Connected

Make sure the ductwork is connected everywhere to all pieces. Disconnected ductwork will permit hot air leak out and of course increase the running costs.

Return Air Inlets And Zone Dampers

Make certain that that return air intakes are free of debris and dust so air can easily flow. Check your dampers to verify that they are in the right position. Through the year we may change the positioning of the damper for many reasons (i.e. getting into a tight space or making room for storage). Check to notice that the dampers are in the correct position too.

If this is a tad too much to handle alone, we propose you hire an area plumbing business licensed for furnace and heating repair. You should be able to locate a good heating company who will take care of this for you. The best advice we can provide is to set up yearly maintenance for that appliance.

As a person who reads on Boiler Service, I assumed sharing that article post was smart. Do you know about another person who is fascinated with the niche? Do not hesitate to promote it. Many thanks for going through it.